全尾砂和废石联合胶结充填体最佳配比及应用

针对红岭铅锌矿分级充填骨料来源不足、地表废石堆积污染环境的情况,提出将该矿选厂产生的全尾砂和地表废石作为充填骨料的联合胶结充填方案。分别测试了全尾砂和地表废石的物理化学性质,验证了碎石和全尾砂作为联合充填骨料的可行性。通过充填配比试验,分析了不同配比全尾砂废石充填体强度特性,得出了最佳充填配比。结果表明,充填试块的强度随灰砂比减小而减小,随养护龄期增加呈增大趋势,随充填料浆质量浓度增大而增大,最佳配比为: 胶结充填灰砂比1∶8、普通充填灰砂比1∶12,全尾砂∶废石配比4∶6,质量浓度78%。根据研究结果,在红岭铅锌矿进行了全尾砂废石充填技术工业应用,证实该技术可行。     

A facile pathway to prepare molybdenum boride powder from molybdenum and boron carbide

Molybdenum boride is an ideal hard and wear-resistant material. In this study, a new method is proposed for preparing molybdenum boride, by which Mo first reacts with B₄C to generate the mixture of molybdenum boride and C, and then the product is decarburized by molten Ca to generate CaC₂. Pure molybdenum boride could be obtained after acid leaching to remove the by-product CaC₂. According to the experimental and thermodynamic calculation results, it is concluded that the single-phase MoB could be successfully prepared, while Mo₂B, Mo₂B₅, and MoB₄ could not be synthesized by this method. Moreover, it was found that the particle size of finally prepared MoB is determined by particle size of raw Mo powder. The residual carbon content of the product could be decreased to 0.10 wt% after first reaction at 1673 K for 6 hours and then decarburization reaction at 1673 K for 6 hours.     

Effect of residual excess carbon on the densification of ultra-fine HfC powder

The residual carbon content of ultra-fine hafnium carbide (HfC) powder was controlled by the optimization of the synthesis process, and the effect of residual carbon on the densification of HfC powder was analyzed. The amount of residual carbon in the HfC powder could be reduced by the de-agglomeration of HfO₂ powder before the carbo-thermal reduction (CTR) process. The average particle size of HfO₂ powder decreased from 230 to 130 nm after the de-agglomeration treatment. Ultra-fine (d₅₀: 110 nm) and highly pure (metal basis purity: >99.9 % except for Zr) HfC powder was obtained after the CTR at 1600 °C for 1 h using the C/Hf mixing ratio of 3.3. In contrast, the C/Hf ratio increased to 3.6 without the de-agglomeration treatment, indicating that a large amount of excess carbon was required for the complete reduction of the agglomerated HfO₂ particles. HfC ceramics with high relative density (>98 %) were obtained after spark plasma sintering at 2000 °C under 80 MPa pressure when using the HfC powder with low excess carbon content. In contrast, the densification did not complete at a higher temperature (2300 °C) and pressure (100 MPa) when the HfC powder contained a large amount of residual carbon. The results clearly indicated that residual carbon suppressed the densification of HfC powder in case the carbide powder had low oxygen content, and the residual carbon content could be controlled by the optimization of the synthesis process. The average grain size and Vickers hardness of the sintered specimen were 6.7(±0.7) μm and 19.6 GPa, respectively.     

A first-principles investigation on mechanical and metallic properties of titanium carbides under pressure

The titanium carbides are potential candidates to achieve both high hardness and refractory property. We carried out a structural search for titanium carbides at three pressures of 0 GPa, 30 GPa and 50 GPa. A phase diagram of the Ti-C system at 0 K was obtained by elucidating formation enthalpies as a function of compositions, and their mechanical and metallic properties of titanium carbides were investigated systematically. We also discussed the relation of titanium concentration to the both mechanical and metallic properties of titanium carbides. It has been found that the average valence electron density and tractility improved at higher concentrations of titanium, while the degree of covalent bonding directionality decreased. To this effect, the hardness of titanium carbide decreases as the content of titanium increases. Our results indicated that the titanium content significantly affected the metallic properties of the Ti-C system.     

基于P波模量的原位胶结充填体强度预测模型研究

原位胶结充填体质量评价通常采用单轴抗压强度作为表征指标,由于在现场工程中无法快速、准确获取充填体的强度值,因此需要建立一种参数易于获取且准确的原位胶结充填体强度预测模型。基于胶结充填体物理力学参数的内在联系,从量纲平衡的角度探索了胶结充填体单轴抗压强度与P波模量的关系。根据C矿和I矿两种原位胶结充填体的密度、P波速度及取芯强度的测试数据,采用线性拟合的方法获得了基于P波模量的原位胶结充填体强度预测模型。通过对C矿和I矿的强度预测模型拟合效果分析可知,P波模量与取芯强度呈正相关性,且拟合效果较好,证明原位胶结充填体强度预测模型精度高,具有很强的实用性。     

粉煤灰超细玻珠复配轻集料在固井低密度水泥浆中的作用

阐述了粉煤灰超细玻珠复配轻集料在固井低密度水泥浆中对其流变性能、强度、质量均匀性以及密度的影响和作用机理。表明该复配轻集料可以明显改善水泥浆的流动性、保水性以及水泥与高效外加剂的相容性,水泥石抗压和抗折强度有显著改善,水泥浆具有良好的质量均匀性,用该集料配制的超低密度水泥浆能满足固井要求,并由此提高固井的经济性。     

预处理工艺对硬质合金与金刚石膜间粘结力的影响

在两种经不同预处理的硬质合金YG8基底上，采用微波等离子体化学气相沉积法，在微波功率2kW，压强4.0kPa和6.5kPa，CH4和H2流量分别为1.6cm/s和100.0cm/s的条件下生长金刚石薄膜。利用X射线衍射检测了金刚石薄膜是否存在，用拉曼光谱分析了薄膜的质量，用金相显微镜观察了薄膜的洛氏硬度压痕，标定并比较了不同预处理工艺膜与基底的结合力。实验结果表明，不同的预处理方法对于粘结力的影响不大，最主要的因素是钴含量的多少。     

共晶碳化物团球化对铸铁激光熔敷层抗裂性的影响

为提高铸铁表面大面积激光熔敷层抗裂性问题，通过冶金因元素控制熔敷层组织形态在熔敷材料中加入碱金属元素钾，研究了在激光快速加热条件下钾对铸铁激光熔敷层组织团球化的影响，进而分析了该球状组织对熔敷层抗裂性的影响，结果表明随熔敷金属内钾含量增多熔敷层内共晶碳化物组织呈球状及孤岛状，这种组织明显提高了熔敷层抗裂性，此外大量的渗碳体组织确保了熔敷层具有较高的耐磨性；获得了无裂纹的大面积搭接熔敷层，其对应合金系统为Fe-C-Si-Ni-K。     

硬质合金长条薄片弯曲变形的控制

从毛坯厚度差、装舟方式、冷却速度、舟皿涂料等方面分析了YG8和J12硬质合金长条薄片的弯曲变形原因,提出了几种抑制弯曲变形的措施。     

中国硬质合金工业现状及发展趋势

简要总结了中国硬质合金工业所取得的成就及与国外先进水平比较存在的差距,并对国内外硬质合金市场和技术发展趋势进行了分析。